UEFA Champions League live

List of the contents of this article:

• 1、 How to stick the car film?
• 2, correct pasting of car film Law
• 3、carHow to apply film
• 4,UEFA Champions League live How to apply car film?

How to stick the car film?

1. The correct way to apply the car film is 5 steps: wash the car, measure the size, apply the film, shape it, and check for bubbles.

2. Clean the car body and keep it dry. Determine the position that needs to be pasted. Under normal circumstances, slowly paste it, scrape it flat with a tool, and remove the bottom paper. If the graphics are too small, you can also tear off all the transparent transfer film and stickers before pasting.But you must be careful not to cause accidental adhesion.

3. The first step is to choose a relatively closed space, avoid using fiber towels and cotton clothes, and prepare to use materials: a large amount of filtered water, scissors, towels, sprayers, scrapers, etc. The second step is to find a clean piece of glass, spray water on it, stick the car film on the glass, and remove the molding paper from the car film.

4. Cut the car film and use the film tool to paste the car mold on the car. The specific operation steps are as follows: Before applying the film, first ensure that the working environment meets the requirements of dryness and less dust. Otherwise, dust debris will enter during work, which will affect the film effect. It is recommended to wash the car before applying the film.

car The correct way to apply the film

Tear open the film, spray water evenly on the effective film surface, and put the torn plastic film aside for later use.

The specific steps of car film are as follows: external cleaning, move clockwise along the car (starting from the "1 o'clock" position, the position of the passenger's front side door), the outer surface of each glass should be thoroughly cleaned, the potential dust should be controlled to a minimum extent, and each glass should be slightly lowered to scrub the top of the glass. Department, because there is more dust there.

Step 1: Fill the sprayer with water first. You can add a few drops of detergent or water appropriately. Step 2: Spray water on the first car glass. Step 3: After spraying water, it is to cut the approximate size of the film first.

The correct way to apply car film is 5 steps: wash the car, measure the size, apply the film, shape it, and check for bubbles.

Cut the car film and use the film tool to stick the car mold on the car. The specific operation steps are as follows: Before applying the film, first ensure that the working environment meets the requirements of dryness and less dust. Otherwise, dust debris will enter during work, which will affect the film effect. It is recommended to wash the car before applying the film.

How to stick the car film

1. Cut the car film and use the film tool to stick the car mold to the car.The specific operation steps are as follows: Before applying the film, first ensure that the working environment meets the requirements of dryness and less dust. Otherwise, dust debris will enter during work, which will affect the film effect. It is recommended to wash the car before applying the film.

2. Clean the car body and keep it dry. Determine the position that needs to be pasted. Under normal circumstances, slowly paste it, scrape it flat with a tool, and remove the bottom paper. If the graphics are too small, you can also tear off all the transparent transfer film and stickers before pasting. But you must be careful not to cause accidental adhesion.

3. The correct way to apply the car film is 5 steps: wash the car, measure the size, apply the film, fix it, and check for bubbles.

4. First, measure the size of the glass to be filmed, then cut out the basically suitable film, and then stick the cut film on the sprayed glass and trim it according to the shape of the glass.

5. Step 4: Apply the film. Tear off the film, spray water evenly on the effective film surface, and put the torn plastic film aside for later use.

How to apply car film?

Clean the car body and keep it dry. Determine the position that needs to be pasted. Under normal circumstances, slowly paste it, scrape it flat with a tool, and remove the bottom paper. If the graphics are too small, you can also tear off all the transparent transfer film and stickers before pasting. But you must be careful not to cause accidental adhesion.

After the baking film is completed, you can officially apply the film, spray the inner glass with water or window film installation liquid, and then tear off the innermost plastic film from the car film, and then stick the car film to the inner glass and move it to the most appropriate position.

Peel the film outward, and after careful sliding and positioning, begin to cut the size of the window film around the edge. During the cutting process, the car film is firmly attached to the glass. Skilled installers can cut the frame directly with bare hands, and the frame will not be damaged when cutting.

The steps of pasting the car film include external cleaning, contour cutting, hot shaping, cleaning the inner surface of the glass, peeling off the protective film, checking and sealing the edges.

Tear off the film, spray water evenly on the effective film surface, and put the torn plastic film aside for later use.